• Power Electronics And Renewable Energy Research Laboratory (PEARL) - V2
  • marizan@um.edu.my
logo
logo

A New Five Level Active Neutral Point Clamped Converter for Equal Losses Distribution and Voltage Balancing

Three-level neutral point (3L-NPC) converter is one of the main topology in the industrial applications and standard converter in medium-voltage applications.

Read More

Transformer-less Online Uninterruptible Power Supply (UPS) system

Uninterruptible power supply (UPS) is widely used to supply power to critical load and provides protection against power failure and other anomalies of power line.

Read More

A 12 Sector-Based Switching Scheme for Abnormal Grid-Connected Ultra-Sparse Z-Source Matrix Converter Based DTC of IM Drive

This research presents a direct torque control (DTC) switching scheme based on ultra-sparse Z-source matrix converter (USZSMC) using 12-side polygonal space vector for variable speed control of an induction motor (IM).

Read More

High efficient single-phase grid-tied transformer less PV inverter with low leakage current

Recently, there has been an increasing interest on transformerless photovoltaic (PV) inverter due to the benefits of lower cost, smaller size and weight, and higher efficiency compared to the ones with transformer.

Read More

Three Phase Shunt Hybrid Active Power Filter Based on Modified Synchronous Reference Frame Theory

Due to the increase in the number and application of nonlinear power electronic equipment a mass of harmonic current and reactive power flow into the network.

Read More

Modified Model Predictive Control of Bidirectional AC-DC And Isolated DC-DC Converters for Energy Storage System

Energy storage systems have been increasingly employed in utility and transport applications as well as in renewable energy sources to ensure power reliability, active power control, load leveling, frequency control and grid synchronization.

Read More

Model Predictive Control With Weithing Factor Optimization For Torque Ripple Reduction of Induction Machine Fed by Indirect Matrix Converter

A finite control set-model predictive control (FCS-MPC) has emerged as a powerful control tool in the field of power converter and drives system.

Read More

Thermal Performance Enhancement of Evacuated Tube Solar Collector Using Nanofluids

Solar energy is the most available, environmental friendly energy source and renewable to sustain the growing energy demand. .

Read More

Transformerless Photovoltaic Inverter with MPPT Controller for Photovoltaic Array Under Partial Shading Condition

In order to overcome the self-heating issue in the photovoltaic (PV) module during the partial shading condition, the bypass diode is added into the PV module.

Read More

Soft-switching Active Clamp Flyback Converter for PV Applications

Grid-connected photovoltaic (PV) system has received a great attention due to the elimination of battery cost in distributed power generation system.

Read More

A Frequency Adaptive Phase Shift Modulation Control Based LLC Series Resonant Converter for Wide Input Voltage Application

Bi-directional DC/DC converters (BDCs) are widely used in many electric power applications such as automobiles, electric vehicles, renewable energy sources, uninterrupted power supplies (UPS), DC micro grid with energy storage systems (ESSs) and so on

Read More

A New Switching Algorithm Based On Single Phase Modulator for Z-Source Inverters With Reduced Computation Time and Enhanced Output Voltage

The inverter is one of the most common power electronics device used in industrial application. The main objective of the inverter is to produce an ac output waveform from a dc source.

Read More

A Dynamic Wireless EV Charging System with Uniform Coupling Factor and Negligible Power Transfer Fluctuation

To minimize the dependency on the petroleum products, electric vehicles (EV) have been selected as a feasible solution for transportation purpose.

Read More

Model Predictive Control Based On Lyapunov Function and Near State Vector Selection of Four-Leg Inverter

Due to the evolution of high processing microprocessors, the model predictive control (MPC) has been widely used in power electronic applications.

Read More

Design of A Modified Class EF2 Inverter For Electric Vechile Charging Through Wireless Power Transfer

Wireless power transfer (WPT) also referred as inductive power transfer (IPT) has the huge potentiality to revolutionize our way of electricity usage.

Read More

Model Predictive Current and Reactive Power Control Fed by Multilevel Four-leg Indirect Matrix Converter Operating Under Unbaalanced Voltage Supply

This research works focused on model-based predictive current control which was applied to indirect matrix converter.

Read More

Fractional Order Sliding Mode Control for Speed Control of PMSM

A fractional order sliding mode control with PID sliding surface design (FOSMC-PID) is proposed in this research.

Read More

System Integration of Wireless Charging Technology for Electric Vehicles (22 kW): PV099-2021

Design, development, and real-world implementation of a 22 kW wireless charging system for electric buses, featuring custom transmitter and receiver coils, power electronics, and an LCC-S compensation network for efficient power transfer across a 200 mm air gap.

Read More

Development of Wireless Opportunity Charging for Last Mile Autonomous Delivery Vehicle and Its Battery Management System

The proposed wireless power transfer (WPT) system for the scrubber comprises a primary transmitter and a secondary receiver coupled via a high-frequency magnetic coil pair. Grid power is converted into high-frequency AC by a front-end inverter and primary compensation network, enabling efficient wireless energy transmission across the air gap. On the receiver side, the induced power is rectified and regulated by a back-end DC-DC converter to deliver stable, controlled charging power to the load.

Read More

Market Validation of Dynamic Wireless Charging for Personal E-Mobility

In this report the proposed dynamic system is presented and tested under real environmental conditions. The proposed system consist of 4 set of transmitters that operates combinely. All these transmitters are connected to the single high frequency inverter. This inverter fulfills the excitation requirements of all transmitters. However, a single receiver is designed to handle the required power and transfer it to the battery charger after rectification. The presented results demonstrates the successful operation of the designed dynamic wireless power transfer (DWPT) system.

Read More
 

Solar powered Design for Autonomous Self Driving Mobile Robotic Solution

Designing an MPPT-based DC-DC converter for a battery charging system is a complex process that requires careful consideration of multiple factors, including power efficiency, charging stability, and operational feasibility.

Read More

Last Update: 02/11/2026